background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

1

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

D

Direct Upgrades to TL05x, TL07x, and

TL08x BiFET Operational Amplifiers

D

Greater Than 2

×

 Bandwidth (10 MHz) and

3

×

 Slew Rate (45 V/

µ

s) Than TL07x

D

Ensured Maximum Noise Floor

17 nV/

Hz

D

On-Chip Offset Voltage Trimming for

Improved DC Performance

D

Wider Supply Rails Increase Dynamic

Signal Range to 

±

19 V

     

description

The TLE207x series of JFET-input operational amplifiers more than double the bandwidth and triple the slew

rate of the TL07x and TL08x families of BiFET operational amplifiers. Texas Instruments Excalibur process

yields a typical noise floor of 11.6 nV/

Hz, 17-nV/

Hz ensured maximum, offering immediate improvement in

noise-sensitive circuits designed using the TL07x. The TLE207x also has wider supply voltage rails, increasing

the dynamic signal range for BiFET circuits to 

±

19 V. On-chip zener trimming of offset voltage yields precision

grades for greater accuracy in dc-coupled applications. The TLE207x are pin-compatible with lower

performance BiFET operational amplifiers for ease in improving performance in existing designs.

BiFET operational amplifiers offer the inherently higher input impedance of the JFET-input transistors, without

sacrificing the output drive associated with bipolar amplifiers. This makes them better suited for interfacing with

high-impedance sensors or very low-level ac signals. They also feature inherently better ac response than

bipolar or CMOS devices having comparable power consumption.

The TLE207x family of BiFET amplifiers are Texas Instruments highest performance BiFETs, with tighter input

offset voltage and ensured maximum noise specifications. Designers requiring less stringent specifications but

seeking the improved ac characteristics of the TLE207x should consider the TLE208x operational amplifier

family.

Because BiFET operational amplifiers are designed for use with dual power supplies, care must be taken to

observe common-mode input voltage limits and output swing when operating from a single supply. DC biasing

of the input signal is required and loads should be terminated to a virtual ground node at mid-supply. Texas

Instruments TLE2426 integrated virtual ground generator is useful when operating BiFET amplifiers from single

supplies.

The TLE207x are fully specified at 

±

15 V and 

±

5 V. For operation in low-voltage and/or single-supply systems,

Texas Instruments LinCMOS families of operational amplifiers (TLC- and TLV-prefix) are recommended. When

moving from BiFET to CMOS amplifiers, particular attention should be paid to slew rate and bandwidth

requirements and output loading.

Copyright 

©

 2000, Texas Instruments Incorporated

PRODUCTION DATA information is current as of publication date.

Products conform to specifications per the terms of Texas Instruments

standard warranty. Production processing does not necessarily include

testing of all parameters.

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of

Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

2

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2071 AVAILABLE OPTIONS

PACKAGED DEVICES

TA

VIOmax

AT 25

°

C

SMALL

OUTLINE†

(D)

CHIP CARRIER

(FK)

CERAMIC DIP

(JG)

PLASTIC DIP

(P)

CHIP FORM‡

(Y)

0

°

C to 70

°

C

2 mV

TLE2071ACD

TLE2071ACP

0

°

C to 70

°

C

4 mV

TLE2071CD

TLE2071CP

TLE2071Y

40

°

C to 85

°

C

2 mV

TLE2071AID

TLE2071AIP

– 40

°

C to 85

°

C

4 mV

TLE2071ID

TLE2071IP

55

°

C to 125

°

C

2 mV

TLE2071AMFK

TLE2071AMJG

– 55

°

C to 125

°

C

4 mV

TLE2071MFK

TLE2071MJG

† The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2071ACDR).

‡ Chip-form versions are tested at TA = 25

°

C.

TLE2072 AVAILABLE OPTIONS

PACKAGED DEVICES

CHIP

TA

VIOmax

AT 25

°

C

SMALL

OUTLINE†

(D)

CHIP

CARRIER

(FK)

CERAMIC

DIP

(JG)

PLASTIC

DIP

(P)

CHIP

FORM‡

(Y)

0

°

C to 70

°

C

3.5 mV

TLE2072ACD

TLE2072ACP

0

°

C to 70

°

C

6 mV

TLE2072CD

TLE2072CP

TLE2072Y

40

°

C to 85

°

C

3.5 mV

TLE2072AID

TLE2072AIP

– 40

°

C to 85

°

C

6 mV

TLE2072ID

TLE2072IP

55

°

C to 125

°

C

3.5 mV

TLE2072AMFK

TLE2072AMJG

– 55

°

C to 125

°

C

6 mV

TLE2072MFK

TLE2072MJG

† The D packages are available taped and reeled. Add R suffix to device type (e.g., TLE2072ACDR).

‡ Chip-form versions are tested at TA = 25

°

C.

TLE2074 AVAILABLE OPTIONS

PACKAGED DEVICES

CHIP

TA

VIOmax

AT 25

°

C

SMALL

OUTLINE†

(DW)

CHIP

CARRIER

(FK)

CERAMIC

DIP

(J)

PLASTIC

DIP

(N)

CHIP

FORM‡

(Y)

0

°

C to 70

°

C

3 mV

TLE2074ACDW

TLE2074ACN

0

°

C to 70

°

C

5 mV

TLE2074CDW

TLE2074CN

TLE2074Y

40

°

C to 85

°

C

3 mV

TLE2074AIDW

TLE2074AIN

– 40

°

C to 85

°

C

5 mV

TLE2074IDW

TLE2074IN

55

°

C to 125

°

C

3 mV

TLE2074AMFK

TLE2074AMJ

– 55

°

C to 125

°

C

5 mV

TLE2074MFK

TLE2074MJ

†  The DW packages are available taped and reeled. Add R suffix to device type (e.g., TLE2074ACDWR).

‡ Chip-form versions are tested at TA = 25

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

3

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

1

2

3

4

8

7

6

5

OFFSET N1

IN –

IN +

V

CC –

NC

V

CC +

OUT

OFFSET N2

3

2

1 20 19

9 10 11 12 13

4

5

6

7

8

18

17

16

15

14

NC

V

CC +

NC

OUT

NC

NC

IN –

NC

IN +

NC

NC

OFFSET

 N1

NC

NC

NC

NC

V

NC

OFFSET

 N2

NC

CC –

NC – No internal connection

TLE2071 AND TLE2071A

D, JG, OR P PACKAGE

(TOP VIEW)

TLE2071M AND TLE2071AM

FK PACKAGE

(TOP VIEW)

1

2

3

4

8

7

6

5

1OUT

1IN –

1IN +

V

CC –

V

CC +

2OUT

2IN –

2IN+

3

2

1 20 19

9 10 11 12 13

4

5

6

7

8

18

17

16

15

14

NC

2OUT

NC

2IN –

NC

NC

1IN –

NC

1IN+

NC

NC

1OUT

NC

NC

NC

NC

V

NC

2IN+

CC –

V

CC +

TLE2072 AND TLE2072A

D, JG, OR P PACKAGE

(TOP VIEW)

TLE2072M AND TLE2072AM

FK PACKAGE

(TOP VIEW)

3

2

1 20 19

9 10 11 12 13

4

5

6

7

8

18

17

16

15

14

4IN+

NC

V

CC –

NC

3IN+

1IN+

NC

V

CC +

NC

2IN+

1IN –

1OUT

NC

3IN –

4IN –

2IN –

NC

3OUT

2OUT

4OUT

1

2

3

5

6

7

8

16

15

14

13

12

11

10

9

1OUT

1IN –

1IN +

V

CC +

2IN +

2IN –

2OUT

NC

4OUT

4IN –

4IN +

V

CC –

3IN +

3IN –

3OUT

NC

1

2

3

5

6

7

14

13

12

11

10

9

8

1OUT

1IN –

1IN +

V

CC +

2IN +

2IN –

2OUT

4OUT

4IN –

4IN +

V

CC –

3IN +

3IN –

3OUT

TLE2074 AND TLE2074A

DW PACKAGE

(TOP VIEW)

TLE2074 AND TLE2074A

J OR N PACKAGE

(TOP VIEW)

TLE2074M AND TLE2074AM

FK PACKAGE

(TOP VIEW)

symbol

+

OUT

IN +

IN –

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

4

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2071Y chip information

This chip, when properly assembled, displays characteristics similar to the TLE2071C. Thermal compression

or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with

conductive epoxy or a gold-silicon preform.

BONDING PAD ASSIGNMENTS

CHIP THICKNESS: 15 TYPICAL

BONDING PADS: 4 

×

 4 MINIMUM

TJmax = 150

°

C

TOLERANCES ARE 

±

10%.

ALL DIMENSIONS ARE IN MILS.

PIN (4) IS INTERNALLY CONNECTED

TO BACKSIDE OF THE CHIP.

+

OUT

 IN +

IN –

VCC +

(6)

(3)

(2)

(5)

(1)

(7)

(4)

OFFSET N1

OFFSET N2

VCC –

58

85

(1)

(2)

(4)

(5)

(6)

(7)

(8)

(3)

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

5

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2072Y chip information

This chip, when properly assembled, displays characteristics similar to the TLE2072C. Thermal compression

or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with

conductive epoxy or a gold-silicon preform.

BONDING PAD ASSIGNMENTS

CHIP THICKNESS: 15 TYPICAL

BONDING PADS: 4 

×

 4 MINIMUM

TJmax = 150

°

C

TOLERANCES ARE 

±

10%.

ALL DIMENSIONS ARE IN MILS.

PIN (4) IS INTERNALLY CONNECTED

TO BACKSIDE OF THE CHIP.

+

1OUT

1IN +

1IN –

VCC+

(4)

(6)

(3)

(2)

(5)

(1)

(7)

(8)

+

2OUT

2IN +

2IN –

VCC –

80

90

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

6

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2074Y chip information

This chip, when properly assembled, displays characteristics similar to the TLE2074C. Thermal compression

or ultrasonic bonding may be used on the doped-aluminum bonding pads. Chips may be mounted with

conductive epoxy or a gold-silicon preform.

BONDING PAD ASSIGNMENTS

CHIP THICKNESS: 15 TYPICAL

BONDING PADS: 4 

×

 4 MINIMUM

TJmax = 150

°

C

TOLERANCES ARE 

±

10%.

ALL DIMENSIONS ARE IN MILS.

PIN (11) IS INTERNALLY CONNECTED

TO BACKSIDE OF THE CHIP.

+

1OUT

1IN +

1IN –

VCC+

(11)

(6)

(3)

(2)

(5)

(1)

(7)

(4)

+

2 OUT

2IN +

2IN –

VCC –

+

3OUT

3IN +

3IN –

(13)

(10)

(9)

(12)

(8)

(14)

+

4OUT

4IN +

4IN –

(2)

(1)

(14)

(4)

(5)

(6)

(7)

(8)

(9)

(10)

(11)

(12)

(13)

100

150

(3)

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW

-NOISE HIGH-SPEED

JFET

-INPUT OPERA

TIONAL

 AMPLIFIERS

SLOS181A

 – FEBRUAR

Y

 1997 – REVISED MARCH 2000

POST

 OFFICE BOX 655303     DALLAS, 

TEXAS 

75265

7

equivalent schematic

Q1

IN –

IN +

Q2

D1

Q7

Q5

Q6

Q9

Q10

C2

R4

Q14

Q4

Q3

R1

Q8

R2

Q11

R3

C1

Q12

D2

Q13

Q15

Q16

Q19

Q20

Q17

R6

VCC –

VCC +

R8

C3

Q18

R7

R5

C4

Q21

C5

R9

R10

Q22

Q26

Q27

Q31

R14

Q29

C6

Q25

Q30

R11

Q23

Q28

Q24

D3

OUT

R13

R12

OFFSET N1

(see Note A)

OFFSET N2

(see Note A)

NOTES: A. OFFSET N1 AND OFFSET N2 are only availiable on the TLE2071x devices.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW

-NOISE HIGH-SPEED

JFET

-INPUT OPERA

TIONAL

 AMPLIFIERS

SLOS181A

 – FEBRUAR

Y

 1997 – REVISED MARCH 2000

T

emp

late 

R

e

lease 

D

ate: 

7

11

94

8

POST

 OFFICE BOX 655303     DALLAS, 

TEXAS 

75265

equivalent schematic (continued)

ACTUAL DEVICE COMPONENT COUNT

COMPONENT

TLE2071

TLE2072

TLE2074

Transistors

33

57

114

Resistors

25

37

74

Diodes

8

5

10

Capacitors

6

11

22

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

9

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)

Supply voltage, V

CC +

 (see Note 1) 

19 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Supply voltage, V

CC –

 (see Note 1) 

– 19 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Differential input voltage range, V

ID

 (see Note 2) 

V

CC +

 to V

CC –

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Input voltage range, V

I

 (any input) 

V

CC +

 to V

CC –

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Input current, I

I

 (each input) 

±

1 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Output current, I

O

 (each output) 

±

80 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Total current into V

CC +

 

160 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Total current out of V

CC –

 

160 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Duration of short-circuit current at (or below) 25

°

C (see Note 3) 

unlimited

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Continuous total dissipation 

See Dissipation Rating Table

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Operating free-air temperature range, T

A

: C suffix 

0

°

C to 70

°

C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

I suffix 

– 40

°

C to 85

°

C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

M suffix 

– 55

°

C to 125

°

C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Storage temperature range 

– 65

°

C to 150

°

C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Case temperature for 60 seconds: FK package 

260

°

C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: DW or N package 

260

°

C

. . . . . . . . . . . . . . . 

Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J package 

300

°

C

. . . . . . . . . . . . . . . . . . . . . 

† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and

functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES:

1. All voltage values, except differential voltages, are with respect to the midpoint between VCC + and VCC – .

2. Differential voltages are at the noninverting input with respect to the inverting input.

3. The output may be shorted to either supply. Temperatures and/or supply voltages must be limited to ensure that the maximum

dissipation rate is not exceeded.

DISSIPATION RATING TABLE

PACKAGE

TA 

 25

°

C

POWER RATING

DERATING FACTOR

ABOVE TA = 25

°

C

TA = 70

°

C

POWER RATING

TA = 85

°

C

POWER RATING

TA = 125

°

C

POWER RATING

D

 725 mW

5.8 mW/

°

C

464 mW

377 mW

DW

1025 mW

8.2 mW/

°

C

656 mW

533 mW

205 mW

FK

1375 mW

11.0 mW/

°

C

880 mW

715 mW

275 mW

J

1375 mW

11.0 mW/

°

C

880 mW

715 mW

275 mW

JG

1050 mW

8.4 mW/

°

C

672 mW

546 mW

210 mW

N

1150 mW

9.2 mW/

°

C

736 mW

598 mW

230 mW

P

1000 mW

8.0 mW/

°

C

640 mW

344 mW

recommended operating conditions

C SUFFIX

I SUFFIX

M SUFFIX

UNIT

MIN

MAX

MIN

MAX

MIN

MAX

UNIT

Supply voltage, VCC

±

±

2.25

±

19

±

2.25

±

19

±

2.25

±

19

V

Common mode input voltage VIC

VCC

±

 = 

±

5 V

– 0.9

5

– 0.8

5

– 0.8

5

V

Common-mode input voltage, VIC

VCC

±

 = 

±

15 V

– 10.9

15

– 10.8

15

– 10.8

15

V

Operating free-air temperature, TA

0

70

– 40

85

– 55

125

°

C

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

10

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2071C electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

T †

TLE2071C

TLE2071AC

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

VIO

Input offset voltage

25

°

C

0.34

4

0.3

2

mV

VIO

Input offset voltage

VIC = 0,

VO = 0,

Full range

6

4

mV

α

VIO

Temperature coefficient

of input offset voltage

RS = 50 

Full range

3.2

29

3.2

29

µ

V/

°

C

IIO

Input offset current

25

°

C

5

100

5

100

pA

IIO

Input offset current

VIC = 0,

VO = 0,

Full range

1.4

1.4

nA

IIB

Input bias current

IC

,

O

,

See Figure 4

25

°

C

15

175

15

175

pA

IIB

Input bias current

Full range

5

5

nA

5

5

5

5

25

°

C

5

to

5

to

5

to

5

to

VICR

Common-mode input

RS = 50

– 1

– 1.9

– 1

– 1.9

V

VICR

voltage range

RS = 50 

5

5

V

Full range

5

to

5

to

g

– 0.9

– 0.9

IO = 200

µ

A

25

°

C

3.8

4.1

3.8

4.1

IO = – 200 

µ

A

Full range

3.7

3.7

VOM

Maximum positive peak

IO = 2 mA

25

°

C

3.5

3.9

3.5

3.9

V

VOM +

output voltage swing

IO = – 2 mA

Full range

3.4

3.4

V

IO = 20 mA

25

°

C

1.5

2.3

1.5

2.3

IO = – 20 mA

Full range

1.5

1.5

IO = 200

µ

A

25

°

C

– 3.5

– 4.2

– 3.5

– 4.2

IO = 200 

µ

A

Full range

– 3.4

– 3.4

VOM

Maximum negative peak

IO = 2 mA

25

°

C

– 3.7

– 4.1

– 3.7

– 4.1

V

VOM –

g

output voltage swing

IO = 2 mA

Full range

– 3.6

– 3.6

V

IO = 20 mA

25

°

C

– 1.5

– 2.4

– 1.5

– 2.4

IO = 20 mA

Full range

– 1.5

– 1.5

RL = 600

25

°

C

80

91

80

91

RL = 600

Full range

79

79

AVD

Large-signal differential

VO =

±

2 3 V

RL = 2 k

25

°

C

90

100

90

100

dB

AVD

g

g

voltage amplification

VO = 

±

 2.3 V

RL = 2 k

Full range

89

89

dB

RL = 10 k

25

°

C

95

106

95

106

RL = 10 k

Full range

94

94

ri

Input resistance

VIC = 0

25

°

C

1012

1012

ci

Input capacitance

VIC = 0,

See Figure 5

Common

mode

25

°

C

11

11

pF

i

See Figure 5

Differential

25

°

C

2.5

2.5

zo

Open-loop output 

impedance

f = 1 MHz

25

°

C

80

80

CMRR

Common-mode

VIC = VICRmin,

25

°

C

70

89

70

89

dB

CMRR

rejection ratio

IC

ICR

,

VO = 0,

RS = 50 

Full range

68

68

dB

kSVR

Supply-voltage rejection

VCC

±

 = 

±

5 V to

±

15 V,

25

°

C

82

99

82

99

dB

kSVR

y

g

j

ratio(

VCC

±

/

VIO)

CC

±

VO = 0,

RS = 50 

Full range

80

80

dB

† Full range is 0

°

C to 70

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

11

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2071C electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V (unless

otherwise noted) (continued)

PARAMETER

TEST CONDITIONS

T †

TLE2071C

TLE2071AC

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

ICC

Supply current

VO = 0

No load

25

°

C

1.35

1.6

2.2

1.35

1.6

2.2

mA

ICC

Supply current

VO = 0,

No load

Full range

2.2

2.2

mA

IOS

Short-circuit output 

VO = 0

VID = 1 V

25

°

C

– 35

– 35

mA

IOS

current

VO = 0

VID = – 1 V

25

°

C

45

45

mA

† Full range is 0

°

C to 70

°

C.

TLE2071C operating characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V

PARAMETER

TEST CONDITIONS

T †

TLE2071C

TLE2071AC

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

25

°

C

35

35

SR +

Positive slew rate

VO(PP) = 

±

2.3 V,

AVD

1

RL 2 k

Full

range

23

23

V/

µ

s

AVD = – 1,

RL = 2 k

,

CL = 100 pF,

See Figure 1

25

°

C

38

38

SR –

Negative slew rate

CL = 100  F,

See Figure 1

Full

range

23

23

V/

µ

s

t

Settling time

AVD = – 1,

2-V step,

To 10 mV

25

°

C

0.25

0.25

µ

s

ts

Settling time

,

RL = 1 k

,

CL = 100 pF

To 1 mV

25

°

C

0.4

0.4

µ

s

V

Equivalent input noise

f = 10 Hz

25

°

C

28

55

28

55

nV/

Hz

Vn

q

voltage

f = 10 kHz

25

°

C

11.6

17

11.6

17

nV/

Hz

RS = 20 

,

f = 10 Hz to

6

6

VN(PP)

Peak-to-peak equivalent

See Figure 3

10 kHz

25

°

C

6

6

µ

V

VN(PP)

q

input noise voltage

f = 0.1 Hz to

10 Hz

25

°

C

0.6

0.6

µ

V

In

Equivalent input noise

current

VIC = 0,

f = 10 kHz

25

°

C

2.8

2.8

fA/

Hz

THD + N

Total harmonic distortion

VO(PP) = 5 V,

AVD = 10,

f = 1 kHz

RL = 2 k

25

°

C

0 013%

0 013%

THD + N

plus noise

f = 1 kHz,

RL = 2 k

,

RS = 25 

25

°

C

0.013%

0.013%

B1

Unity gain bandwidth

VI = 10 mV,

RL = 2 k

,

25

°

C

9 4

9 4

MHz

B1

Unity-gain bandwidth

I

,

L

,

CL = 25 pF,

See Figure 2

25

°

C

9.4

9.4

MHz

BOM

Maximum output-swing

VO(PP) = 4 V,

AVD = – 1,

25

°

C

2 8

2 8

MHz

BOM

g

bandwidth

O(PP)

,

VD

,

RL = 2 k

 

,

CL = 25 pF

25

°

C

2.8

2.8

MHz

φ

Phase margin at unity

VI = 10 mV,

RL = 2 k

,

25

°

C

56

°

56

°

φ

m

g

y

gain

I

L

CL = 25 pF,

See Figure 2

25

°

C

56

°

56

°

† Full range is 0

°

C to 70

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

12

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2071C electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

T †

TLE2071C

TLE2071AC

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

VIO

Input offset voltage

25

°

C

0.49

4

0.47

2

mV

VIO

Input offset voltage

VIC = 0,

VO = 0,

Full range

6

4

mV

α

VIO

Temperature coefficient

of input offset voltage

RS = 50 

Full range

3.2

29

3.2

29

µ

V/

°

C

IIO

Input offset current

25

°

C

6

100

6

100

pA

IIO

Input offset current

VIC = 0,

VO = 0,

Full range

1.4

1.4

nA

IIB

Input bias current

IC

,

O

,

See Figure 4

25

°

C

20

175

20

175

pA

IIB

Input bias current

Full range

5

5

nA

15

15

15

15

25

°

C

15

to

15

to

15

to

15

to

VICR

Common-mode input

RS = 50

– 11

– 11.9

– 11

– 11.9

V

VICR

voltage range

RS = 50 

15

15

V

Full range

15

to

15

to

g

– 10.9

– 10.9

IO = 200

µ

A

25

°

C

13.8

14.1

13.8

14.1

IO = – 200 

µ

A

Full range

13.7

13.7

VOM

Maximum positive peak

IO = 2 mA

25

°

C

13.5

13.9

13.5

13.9

V

VOM +

output voltage swing

IO = – 2 mA

Full range

13.4

13.4

V

IO = 20 mA

25

°

C

11.5

12.3

11.5

12.3

IO = – 20 mA

Full range

11.5

11.5

IO = 200

µ

A

25

°

C

– 13.8

– 14.2

– 13.8

– 14.2

IO = 200 

µ

A

Full range

– 13.7

– 13.7

VOM

Maximum negative peak

IO = 2 mA

25

°

C

– 13.5

– 14

–13.5

– 14

V

VOM –

g

output voltage swing

IO = 2 mA

Full range

– 13.4

– 13.4

V

IO = 20 mA

25

°

C

– 11.5

– 12.4

– 11.5

– 12.4

IO = 20 mA

Full range

– 11.5

– 11.5

RL = 600

25

°

C

80

96

80

96

RL = 600

Full range

79

79

AVD

Large-signal differential

VO =

±

10 V

RL = 2 k

25

°

C

90

109

90

109

dB

AVD

g

g

voltage amplification

VO = 

±

 10 V

RL = 2 k

Full range

89

89

dB

RL = 10 k

25

°

C

95

118

95

118

RL = 10 k

Full range

94

94

ri

Input resistance

VIC = 0

25

°

C

1012

1012

ci

Input capacitance

VIC = 0,

See Figure 5

Common

mode

25

°

C

7.5

7.5

pF

i

See Figure 5

Differential

25

°

C

2.5

2.5

zo

Open-loop output 

impedance

f = 1 MHz

25

°

C

80

80

CMRR

Common-mode

VIC = VICRmin,

25

°

C

80

98

80

98

dB

CMRR

rejection ratio

IC

ICR

,

VO = 0,

RS = 50 

Full range

79

79

dB

kSVR

Supply-voltage rejection

VCC

±

 = 

±

5 V to

±

15 V,

25

°

C

82

99

82

99

dB

kSVR

y

g

j

ratio (

VCC

±

/

VIO)

CC

±

VO = 0,

RS = 50 

Full range

80

81

dB

† Full range is 0

°

C to 70

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

13

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2071C electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V (unless

otherwise noted)

 (continued)

PARAMETER

TEST CONDITIONS

T †

TLE2071C

TLE2071AC

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

ICC

Supply current

VO = 0

No load

25

°

C

1.35

1.7

2.2

1.35

1.7

2.2

mA

ICC

Supply current

VO = 0,

No load

Full range

2.2

2.2

mA

I

Short-circuit output 

V

0

VID = 1 V

25

°

C

– 30

– 45

– 30

– 45

mA

IOS

current

VO = 0

VID = – 1 V

25

°

C

30

48

30

48

mA

† Full range is 0

°

C to 70

°

C.

TLE2071C operating characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V

PARAMETER

TEST CONDITIONS

T †

TLE2071C

TLE2071AC

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

25

°

C

30

40

30

40

SR +

Positive slew rate

VO(PP) = 10 V, AVD = – 1,

RL 2 k

CL 100 pF

Full

range

27

27

V/

µ

s

RL = 2 k

,

CL = 100 pF,

See Figure 1

25

°

C

30

45

30

45

SR –

Negative slew rate

See Figure 1

Full

range

27

27

V/

µ

s

t

Settling time

AVD = – 1,

10-V step, 

To 10 mV

25

°

C

0.4

0.4

µ

s

ts

Settling time

,

RL = 1 k

,

CL = 100 pF

To 1 mV

25

°

C

1.5

1.5

µ

s

V

Equivalent input noise

f = 10 Hz

25

°

C

28

55

28

55

nV

Hz

Vn

q

voltage

f = 10 kHz

25

°

C

11.6

17

11.6

17

nV

Hz

RS = 20 

,

f = 10 Hz to

6

6

VN(PP)

Peak-to-peak equivalent

S

See Figure 3

10 kHz

25

°

C

6

6

µ

V

VN(PP)

q

input noise voltage

f = 0.1 Hz to

25

°

C

0 6

0 6

µ

V

10 Hz

0.6

0.6

I

Equivalent input noise

VIC = 0

f = 10 kHz

25

°

C

2 8

2 8

fA/

Hz

In

q

current

VIC = 0,

f = 10 kHz

25

°

C

2.8

2.8

fA/

Hz

THD + N

Total harmonic distortion

VO(PP) = 20 V, AVD = 10,

f = 1 kHz

RL = 2 k

25

°

C

0 008%

0 008%

THD + N

plus noise

f = 1 kHz,

RL = 2 k

RS = 25 

25

°

C

0.008%

0.008%

B1

Unity gain bandwidth

VI = 10 mV,

RL = 2 k

,

25

°

C

8

10

8

10

MHz

B1

Unity-gain bandwidth

I

,

L

,

CL = 25 pF,

See Figure 2

25

°

C

8

10

8

10

MHz

BOM

Maximum output-swing

VO(PP) = 20 V, AVD = – 1,

25

°

C

478

637

478

637

kHz

BOM

g

bandwidth

O(PP)

,

VD

,

RL = 2 k

,

CL = 25 pF

25

°

C

478

637

478

637

kHz

φ

Phase margin at unity

VI = 10 mV,

RL = 2 k

,

25

°

C

57

°

57

°

φ

m

g

y

gain

I

L

CL = 25 pF,

See Figure 2

25

°

C

57

°

57

°

† Full range is 0

°

C to 70

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

14

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2071I electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V (unless otherwise

noted)

PARAMETER

TEST CONDITIONS

T †

TLE2071I

TLE2071AI

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

VIO

Input offset voltage

25

°

C

0.34

4

0.3

2

mV

VIO

Input offset voltage

VIC = 0,

VO = 0,

Full range

7.6

5.6

mV

α

VIO

Temperature coefficient

of input offset voltage

RS = 50 

Ω,

Full range

3.2

29

3.2

29

µ

V/

°

C

IIO

Input offset current

25

°

C

5

100

5

100

pA

IIO

Input offset current

VIC = 0,

VO = 0,

Full range

5

5

nA

IIB

Input bias current

IC

,

O

,

See Figure 4

25

°

C

15

175

15

175

pA

IIB

Input bias current

Full range

10

10

nA

5

5

5

5

25

°

C

5

to

5

to

5

to

5

to

VICR

Common-mode input

RS = 50

– 1

– 1.9

– 1

– 1.9

V

VICR

voltage range

RS = 50 

5

5

V

Full range

5

to

5

to

g

– 0.8

– 0.8

IO = 200

µ

A

25

°

C

3.8

4.1

3.8

4.1

IO = – 200 

µ

A

Full range

3.7

3.7

VOM

Maximum positive peak

IO = 2 mA

25

°

C

3.5

3.9

3.5

3.9

V

VOM +

output voltage swing

IO = – 2 mA

Full range

3.4

3.4

V

IO = 20 mA

25

°

C

1.5

2.3

1.5

2.3

IO = – 20 mA

Full range

1.5

1.5

IO = 200

µ

A

25

°

C

– 3.8

– 4.2

– 3.8

– 4.2

IO = 200 

µ

A

Full range

– 3.7

– 3.7

VOM

Maximum negative peak

IO = 2 mA

25

°

C

– 3.5

– 4.1

– 3.5

– 4.1

V

VOM –

g

output voltage swing

IO = 2 mA

Full range

– 3.4

– 3.4

V

IO = 20 mA

25

°

C

– 1.5

– 2.4

– 1.5

– 2.4

IO = 20 mA

Full range

– 1.5

– 1.5

RL = 600

25

°

C

80

91

80

91

RL = 600

Full range

79

79

AVD

Large-signal differential

VO =

±

2 3 V

RL = 2 k

25

°

C

90

100

90

100

dB

AVD

g

g

voltage amplification

VO = 

±

 2.3 V

RL = 2 k

Full range

89

89

dB

RL = 10 k

25

°

C

95

106

95

106

RL = 10 k

Full range

94

94

ri

Input resistance

VIC = 0

25

°

C

1012

1012

ci

Input capacitance

VIC = 0,

See Figure 5

Common

mode

25

°

C

11

11

pF

i

See Figure 5

Differential

25

°

C

2.5

2.5

zo

Open-loop output 

impedance

f = 1 MHz

25

°

C

80

80

CMRR

Common-mode

VIC = VICRmin,

25

°

C

70

89

70

89

dB

CMRR

rejection ratio

IC

ICR

,

VO = 0,

RS = 50 

Full range

68

68

dB

kSVR

Supply-voltage rejection

VCC

±

 = 

±

5 V to

±

15 V,

25

°

C

82

99

82

99

dB

kSVR

y

g

j

ratio (

VCC

±

/

VIO)

CC

±

,

VO = 0,

RS = 50 

Full range

80

80

dB

† Full range is – 40

°

C to 85

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

15

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2071I electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V (unless otherwise

noted)

 (continued)

PARAMETER

TEST CONDITIONS

T †

TLE2071I

TLE2071AI

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

ICC

Supply current

VO = 0

No load

25

°

C

1.35

1.6

2.2

1.35

1.6

2.2

mA

ICC

Supply current

VO = 0,

No load

Full range

2.2

2.2

mA

IOS

Short-circuit output 

VO = 0

VID = 1 V

25

°

C

– 35

– 35

mA

IOS

current

VO = 0

VID = – 1 V

25

°

C

45

45

mA

† Full range is – 40

°

C to 85

°

C.

TLE2071I operating characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V

PARAMETER

TEST CONDITIONS

T †

TLE2071I

TLE2071AI

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

25

°

C

35

35

SR +

Positive slew rate

VO(PP) = 

±

2.3 V,

AVD

1

RL 2 k

Full

range

22

22

V/

µ

s

AVD = – 1,

RL = 2 k

,

CL = 100 pF, See Figure 1

25

°

C

38

38

SR –

Negative slew rate

CL = 100  F, See Figure 1

Full

range

22

22

V/

µ

s

t

Settling time

AVD = – 1,

2-V step,

To 10 mV

25

°

C

0.25

0.25

µ

s

ts

Settling time

,

RL = 1 k

,

CL = 100 pF

To 1 mV

25

°

C

0.4

0.4

µ

s

V

Equivalent input noise

f = 10 Hz

25

°

C

28

55

28

55

nV/

Hz

Vn

q

voltage

f = 10 kHz

25

°

C

11.6

17

11.6

17

nV/

Hz

RS = 20 

,

f = 10 Hz  to

6

6

VN(PP)

Peak-to-peak equivalent

S

See Figure 3

10 kHz

25

°

C

6

6

µ

V

VN(PP)

q

input noise voltage

f = 0.1 Hz  to

25

°

C

0 6

0 6

µ

V

10 Hz

0.6

0.6

In

Equivalent input noise

current

VIC = 0,

f = 10 kHz

25

°

C

2.8

2.8

fA/

Hz

THD + N

Total harmonic distortion

VO(PP) = 5 V, AVD = 10,

f = 1 kHz

RL = 2 k

25

°

C

0 013%

0 013%

THD + N

plus noise

f = 1 kHz,

RL = 2 k

,

RS = 25 

25

°

C

0.013%

0.013%

B1

Unity gain bandwidth

VI = 10 mV,

RL = 2 k

,

25

°

C

9 4

9 4

MHz

B1

Unity-gain bandwidth

I

,

L

,

CL = 25 pF,

See Figure 2

25

°

C

9.4

9.4

MHz

BOM

Maximum output-swing

VO(PP) = 4 V, AVD = – 1,

25

°

C

2 8

2 8

MHz

BOM

g

bandwidth

O(PP)

,

VD

,

RL = 2 k

 

,

CL = 25 pF

25

°

C

2.8

2.8

MHz

φ

Phase margin at unity gain

VI = 10 mV,

RL = 2 k

,

25

°

C

56

°

56

°

φ

m

Phase margin at unity gain

I

,

L

,

CL = 25 pF,

See Figure 2

25

°

C

56

°

56

°

† Full range is – 40

°

C to 85

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

16

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2071I electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

T †

TLE2071I

TLE2071AI

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

VIO

Input offset voltage

25

°

C

0.49

4

0.47

2

mV

VIO

Input offset voltage

VIC = 0,

VO = 0,

Full range

7.6

5.6

mV

α

VIO

Temperature coefficient

of input offset voltage

RS = 50 

Ω,

Full range

3.2

29

3.2

29

µ

V/

°

C

IIO

Input offset current

25

°

C

6

100

6

100

pA

IIO

Input offset current

VIC = 0,

VO = 0,

Full range

5

5

nA

IIB

Input bias current

IC

,

O

,

See Figure 4

25

°

C

20

175

20

175

pA

IIB

Input bias current

Full range

10

10

nA

15

15

15

15

25

°

C

15

to

15

to

15

to

15

to

VICR

Common-mode input

RS = 50

– 11

– 11.9

– 11

– 11.9

V

VICR

voltage range

RS = 50 

15

15

V

Full range

15

to

15

to

g

– 10.8

– 10.8

IO = 200

µ

A

25

°

C

13.8

14.1

13.8

14.1

IO = – 200 

µ

A

Full range

13.7

13.7

VOM

Maximum positive peak

IO = 2 mA

25

°

C

13.5

13.9

13.5

13.9

V

VOM +

output voltage swing

IO = – 2 mA

Full range

13.4

13.4

V

IO = 20 mA

25

°

C

11.5

12.3

11.5

12.3

IO = – 20 mA

Full range

11.5

11.5

IO = 200

µ

A

25

°

C

– 13.8

– 14.2

– 13.8

– 14.2

IO = 200 

µ

A

Full range

– 13.7

– 13.7

VOM

Maximum negative peak

IO = 2 mA

25

°

C

– 13.5

– 14

–13.5

– 14

V

VOM –

g

output voltage swing

IO = 2 mA

Full range

– 13.4

– 13.4

V

IO = 20 mA

25

°

C

– 11.5

– 12.4

– 11.5

– 12.4

IO = 20 mA

Full range

– 11.5

– 11.5

RL = 600

25

°

C

80

96

80

96

RL = 600

Full range

79

79

AVD

Large-signal differential

VO =

±

10 V

RL = 2 k

25

°

C

90

109

90

109

dB

AVD

g

g

voltage amplification

VO = 

±

 10 V

RL = 2 k

Full range

89

89

dB

RL = 10 k

25

°

C

95

118

95

118

RL = 10 k

Full range

94

94

ri

Input resistance

VIC = 0

25

°

C

1012

1012

ci

Input capacitance

VIC = 0,

See Figure 5

Common

mode

25

°

C

7.5

7.5

pF

i

See Figure 5

Differential

25

°

C

2.5

2.5

zo

Open-loop output 

impedance

f = 1 MHz

25

°

C

80

80

CMRR

Common-mode

VIC = VICRmin,

VO 0

25

°

C

80

98

80

98

dB

CMRR

rejection ratio

VO = 0,

RS = 50 

Full range

79

79

dB

kSVR

Supply-voltage rejection

VCC

±

 = 

±

5 V to

±

15 V,

25

°

C

82

99

82

99

dB

kSVR

y

g

j

ratio (

VCC

±

/

VIO)

CC

±

,

VO = 0,

RS = 50 

Full range

80

80

dB

† Full range is – 40

°

C to 85

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

17

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2071I electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V (unless

otherwise noted)

 (continued)

PARAMETER

TEST CONDITIONS

T †

TLE2071I

TLE2071AI

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

ICC

Supply current

VO = 0

No load

25

°

C

1.35

1.7

2.2

1.35

1.7

2.2

mA

ICC

Supply current

VO = 0,

No load

Full range

2.2

2.2

mA

I

Short-circuit output 

V

0

VID = 1 V

25

°

C

– 30

– 45

– 30

– 45

mA

IOS

current

VO = 0

VID = – 1 V

25

°

C

30

48

30

48

mA

† Full range is – 40

°

C to 85

°

C.

TLE2071I operating characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V

PARAMETER

TEST CONDITIONS

TA†

TLE2071I

TLE2071AI

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

25

°

C

30

40

30

40

SR +

Positive slew rate

VO(PP) = 

±

10 V,

AVD = – 1

RL = 2 k

Full

range

24

24

V/

µ

s

AVD = – 1,

RL = 2 k

,

CL = 100 pF,

See Figure 1

25

°

C

30

45

30

45

SR –

Negative slew rate

CL = 100  F,

See Figure 1

Full

range

24

24

V/

µ

s

t

Settling time

AVD = – 1,

10-V step,

To 10 mV

25

°

C

0.4

0.4

µ

s

ts

Settling time

RL = 1 k

,

CL = 100 pF

To 1 mV

25

°

C

1.5

1.5

µ

s

V

Equivalent input noise

f = 10 Hz

25

°

C

28

55

28

55

nV/

Hz

Vn

q

voltage

f = 10 kHz

25

°

C

11.6

17

11.6

17

nV/

Hz

RS = 20 

,

f = 10 Hz to

6

6

VN(PP)

Peak-to-peak equivalent

See Figure 3

10 kHz

25

°

C

6

6

µ

V

VN(PP)

input noise voltage

f = 0.1 Hz to

10 Hz

25

°

C

0.6

0.6

µ

V

In

Equivalent input noise

current

VIC = 0,

f = 10 kHz

25

°

C

2.8

2.8

fA/

Hz

THD + N

Total harmonic distortion

VO(PP) = 20 V, AVD = 10,

f = 1 kHz

RL = 2 k

25

°

C

0 008%

0 008%

THD + N

plus noise

f = 1 kHz,

RL = 2 k

,

RS = 25 

25

°

C

0.008%

0.008%

B1

Unity gain bandwidth

VI = 10 mV,

RL = 2 k

,

25

°

C

8

10

8

10

MHz

B1

Unity-gain bandwidth

I

L

CL = 25 pF,

See Figure 2

25

°

C

8

10

8

10

MHz

BOM

Maximum output-swing

VO(PP) = 20 V, AVD = – 1,

25

°

C

478

637

478

637

kHz

BOM

g

bandwidth

O(PP)

VD

RL = 2 k

,

CL = 25 pF

25

°

C

478

637

478

637

kHz

φ

m

Phase margin at unity gain

VI = 10 mV,

RL = 2 k

,

25

°

C

57

°

57

°

φ

m

Phase margin at unity gain

I

L

CL = 25 pF,

See Figure 2

25

°

C

57

°

57

°

† Full range is – 40

°

C to 85

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

18

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2071M electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

T †

TLE2071M

TLE2071AM

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

VIO

Input offset voltage

25

°

C

0.34

4

0.3

2

mV

VIO

Input offset voltage

VIC = 0,

VO = 0,

Full range

9.2

7.2

mV

α

VIO

Temperature coefficient

of input offset voltage

RS = 50 

Ω,

Full range

3.2

29

3.2

29

µ

V/

°

C

IIO

Input offset current

25

°

C

5

100

5

100

pA

IIO

Input offset current

VIC = 0,

VO = 0,

Full range

20

20

nA

IIB

Input bias current

IC

,

O

,

See Figure 4

25

°

C

15

175

15

175

pA

IIB

Input bias current

Full range

60

60

nA

5

5

5

5

25

°

C

5

to

5

to

5

to

5

to

VICR

Common-mode input

RS = 50

– 1

– 1.9

– 1

– 1.9

V

VICR

voltage range

RS = 50 

5

5

V

Full range

5

to

5

to

g

– 0.8

– 0.8

IO = 200

µ

A

25

°

C

3.8

4.1

3.8

4.1

IO = – 200 

µ

A

Full range

3.6

3.6

VOM

Maximum positive peak

IO = 2 mA

25

°

C

3.5

3.9

3.5

3.9

V

VOM +

output voltage swing

IO = – 2 mA

Full range

3.3

3.3

V

IO = 20 mA

25

°

C

1.5

2.3

1.5

2.3

IO = – 20 mA

Full range

1.4

1.4

IO = 200

µ

A

25

°

C

– 3.8

– 4.2

– 3.8

– 4.2

IO = 200 

µ

A

Full range

– 3.6

– 3.6

VOM

Maximum negative peak

IO = 2 mA

25

°

C

– 3.5

– 4.1

– 3.5

– 4.1

V

VOM –

g

output voltage swing

IO = 2 mA

Full range

– 3.3

– 3.3

V

IO = 20 mA

25

°

C

– 1.5

– 2.4

– 1.5

– 2.4

IO = 20 mA

Full range

– 1.4

– 1.4

RL = 600

25

°

C

80

91

80

91

RL = 600

Full range

78

78

AVD

Large-signal differential

VO =

±

2 3 V

RL = 2 k

25

°

C

90

100

90

100

dB

AVD

g

g

voltage amplification

VO = 

±

 2.3 V

RL = 2 k

Full range

88

88

dB

RL = 10 k

25

°

C

95

106

95

106

RL = 10 k

Full range

93

93

ri

Input resistance

VIC = 0

25

°

C

1012

1012

ci

Input capacitance

VIC = 0,

See Figure 5

Common

mode

25

°

C

11

11

pF

i

See Figure 5

Differential

25

°

C

2.5

2.5

zo

Open-loop output 

impedance

f = 1 MHz

25

°

C

80

80

CMRR

Common-mode

VIC = VICRmin,

25

°

C

70

89

70

89

dB

CMRR

rejection ratio

IC

ICR

,

VO = 0,

RS = 50 

Full range

68

68

dB

kSVR

Supply-voltage rejection

VCC

±

 = 

±

5 V to

±

15 V,

25

°

C

82

99

82

99

dB

kSVR

y

g

j

ratio (

VCC

±

/

VIO)

CC

±

,

VO = 0,

RS = 50 

Full range

80

80

dB

On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.

† Full range is – 55

°

C to 125

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

19

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2071M electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

T †

TLE2071M

TLE2071AM

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

ICC

Supply current

VO = 0

No load

25

°

C

1.35

1.6

2.2

1.35

1.6

2.2

mA

ICC

Supply current

VO = 0,

No load

Full range

2.2

2.2

mA

I

Short-circuit output 

V

0

VID = 1 V

25

°

C

– 35

– 35

mA

IOS

current

VO = 0

VID = – 1 V

25

°

C

45

45

mA

† Full range is – 55

°

C to 125

°

C.

TLE2071M operating characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V

PARAMETER

TEST CONDITIONS

T †

TLE2071M

TLE2071AM

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

25

°

C

35

35

SR +

Positive slew rate

VO(PP) = 

±

2.3 V,

AVD

1

RL 2 k

Full

range

20

20

V/

µ

s

AVD = – 1,

RL = 2 k

,

CL = 100 pF,

See Figure 1

25

°

C

38

38

SR –

Negative slew rate

CL = 100  F,

See Figure 1

Full

range

20

20

V/

µ

s

t

Settling time

AVD = – 1,

2-V step,

To 10 mV

25

°

C

0.25

0.25

µ

s

ts

Settling time

,

RL = 1 k

,

CL = 100 pF

To 1 mV

25

°

C

0.4

0.4

µ

s

V

Equivalent input noise

f = 10 Hz

25

°

C

28

55

28

55

nV/

Hz

Vn

q

voltage

f = 10 kHz

25

°

C

11.6

17

11.6

17

nV/

Hz

V

Peak-to-peak equivalent

RS = 20 

,

See Figure 3

f = 10 Hz to

10 kHz

25

°

C

6

6

µ

V

VN(PP)

q

input noise voltage

f = 0.1 Hz to

25

°

C

0 6

0 6

µ

V

10 Hz

0.6

0.6

In

Equivalent input noise

current

VIC = 0,

f = 10 kHz

25

°

C

2.8

2.8

fA/

Hz

THD + N

Total harmonic distortion

VO(PP) = 5 V,

AVD = 10,

f

1 kHz

RL 2 k

25

°

C

0 013%

0 013%

THD + N

plus noise

f = 1 kHz,

RL = 2 k

RS = 25 

25

°

C

0.013%

0.013%

B1

Unity gain bandwidth

VI = 10 mV,

RL = 2 k

,

25

°

C

9 4

9 4

MHz

B1

Unity-gain bandwidth

I

,

L

,

CL = 25 pF,

See Figure 2

25

°

C

9.4

9.4

MHz

BOM

Maximum output-swing

VO(PP) = 4 V,

AVD = – 1,

25

°

C

2 8

2 8

MHz

BOM

g

bandwidth

O(PP)

,

VD

,

RL = 2 k

 

,

CL = 25 pF

25

°

C

2.8

2.8

MHz

φ

Phase margin at unity

VI = 10 mV,

RL = 2 k

,

25

°

C

56

°

56

°

φ

m

g

y

gain

I

,

L

,

CL = 25 pF,

See Figure 2

25

°

C

56

°

56

°

On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.

† Full range is – 55

°

C to 125

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

20

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2071M electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

T †

TLE2071M

TLE2071AM

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

VIO

Input offset voltage

25

°

C

0.49

4

0.47

2

mV

VIO

Input offset voltage

VIC = 0,

VO = 0,

Full range

9.2

7.2

mV

α

VIO

Temperature coefficient

of input offset voltage

RS = 50 

Full range

3.2

29

3.2

29

µ

V/

°

C

IIO

Input offset current

25

°

C

6

100

6

100

pA

IIO

Input offset current

VIC = 0,

VO = 0,

Full range

20

20

nA

IIB

Input bias current

IC

,

O

,

See Figure 4

25

°

C

20

175

20

175

pA

IIB

Input bias current

Full range

60

60

nA

15

15

15

15

25

°

C

15

to

15

to

15

to

15

to

VICR

Common-mode input

RS = 50

– 11

– 11.9

– 11

– 11.9

V

VICR

voltage range

RS = 50 

15

15

V

Full range

15

to

15

to

g

– 10.9

– 10.9

IO = 200

µ

A

25

°

C

13.8

14.1

13.8

14.1

IO = – 200 

µ

A

Full range

13.6

13.6

VOM

Maximum positive peak

IO = 2 mA

25

°

C

13.5

13.9

13.5

13.9

V

VOM +

output voltage swing

IO = – 2 mA

Full range

13.3

13.3

V

IO = 20 mA

25

°

C

11.5

12.3

11.5

12.3

IO = – 20 mA

Full range

11.4

11.4

IO = 200

µ

A

25

°

C

– 13.8

– 14.2

– 13.8

– 14.2

IO = 200 

µ

A

Full range

– 13.6

– 13.6

VOM

Maximum negative peak

IO = 2 mA

25

°

C

– 13.5

– 14

–13.5

– 14

V

VOM –

g

output voltage swing

IO = 2 mA

Full range

– 13.3

– 13.3

V

IO = 20 mA

25

°

C

– 11.5

– 12.4

– 11.5

– 12.4

IO = 20 mA

Full range

– 11.4

– 11.4

RL = 600

25

°

C

80

96

80

96

RL = 600

Full range

78

78

AVD

Large-signal differential

VO =

±

10 V

RL = 2 k

25

°

C

90

109

90

109

dB

AVD

g

g

voltage amplification

VO = 

±

 10 V

RL = 2 k

Full range

88

88

dB

RL = 10 k

25

°

C

95

118

95

118

RL = 10 k

Full range

93

93

ri

Input resistance

VIC = 0

25

°

C

1012

1012

ci

Input capacitance

VIC = 0,

See Figure 5

Common

mode

25

°

C

7.5

7.5

pF

i

See Figure 5

Differential

25

°

C

2.5

2.5

zo

Open-loop output

impedance

f = 1 MHz

25

°

C

80

80

CMRR

Common-mode

VIC = VICRmin,

25

°

C

80

98

80

98

dB

CMRR

rejection ratio

IC

ICR

,

VO = 0,

RS = 50 

Full range

78

78

dB

kSVR

Supply-voltage rejection

VCC

±

 = 

±

5 V to

±

15 V,

25

°

C

82

99

82

99

dB

kSVR

y

g

j

ratio (

VCC

±

/

VIO)

CC

±

,

VO = 0,

RS = 50 

Full range

80

80

dB

On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.

† Full range is – 55

°

C to 125

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

21

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2071M electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V (unless

otherwise noted)

 (continued)

PARAMETER

TEST CONDITIONS

T †

TLE2071M

TLE2071AM

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

ICC

Supply current

VO = 0

No load

25

°

C

1.35

1.7

2.2

1.35

1.7

2.2

mA

ICC

Supply current

VO = 0,

No load

Full range

2.2

2.2

mA

I

Short circuit output current

V

0

VID = 1 V

25

°

C

– 30

– 45

– 30

– 45

mA

IOS

Short-circuit output current

VO = 0

VID = – 1 V

25

°

C

30

48

30

48

mA

† Full range is – 55

°

C to 125

°

C.

TLE2071M operating characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V

PARAMETER

TEST CONDITIONS

T †

TLE2071M

TLE2071AM

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

25

°

C

30

40

30

40

SR +

Positive slew rate

VO(PP) = 10 V, AVD = – 1,

RL 2 k

CL 100 pF

Full

range

22

22

V/

µ

s

RL = 2 k

,

CL = 100 pF,

See Figure 1

25

°

C

30

45

30

45

SR –

Negative slew rate

See Figure 1

Full

range

22

22

V/

µ

s

t

Settling time

AVD = – 1,

10-V step, 

To 10 mV

25

°

C

0.4

0.4

µ

s

ts

Settling time

,

RL = 1 k

,

CL = 100 pF

To 1 mV

25

°

C

1.5

1.5

µ

s

V

Equivalent input noise

f = 10 Hz

25

°

C

28

55

28

55

nV/

Hz

Vn

q

voltage

f = 10 kHz

25

°

C

11.6

17

11.6

17

nV/

Hz

RS = 20 

,

f = 10 Hz to

6

6

VN(PP)

Peak-to-peak equivalent

S

See Figure 3

10 kHz

25

°

C

6

6

µ

V

VN(PP)

q

input noise voltage

f = 0.1 Hz to

25

°

C

0 6

0 6

µ

V

10 Hz

0.6

0.6

In

Equivalent input noise

current

VIC = 0,

f = 10 kHz

25

°

C

2.8

2.8

fA/

Hz

THD + N

Total harmonic distortion

VO(PP) = 20 V, AVD = 10,

f

1 kHz

RL 2 k

25

°

C

0 008%

0 008%

THD + N

plus noise

f = 1 kHz,

RL = 2 k

RS = 25 

25

°

C

0.008%

0.008%

B1

Unity gain bandwidth

VI = 10 mV,

RL = 2 k

,

25

°

C

8

10

8

10

MHz

B1

Unity-gain bandwidth

I

,

L

,

CL = 25 pF,

See Figure 2

25

°

C

8

10

8

10

MHz

BOM

Maximum output-swing

VO(PP) = 20 V, AVD = – 1,

25

°

C

478

637

478

637

kHz

BOM

g

bandwidth

O(PP)

,

VD

,

RL = 2 k

,

CL = 25 pF

25

°

C

478

637

478

637

kHz

φ

Phase margin at unity

VI = 10 mV,

RL = 2 k

,

25

°

C

57

°

57

°

φ

m

g

y

gain

I

,

L

,

CL = 25 pF,

See Figure 2

25

°

C

57

°

57

°

On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.

† Full range is – 55

°

C to 125

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

22

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2071Y electrical characteristics at V

CC

±

 = 

±

15 V, T

A

 = 25

°

C

PARAMETER

TEST CONDITIONS

TLE2071Y

UNIT

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

VIO

Input offset voltage

VIC = 0,

VO = 0,

RS = 50 

0.49

4

mV

IIO

Input offset current

VIC = 0

VO = 0

See Figure 4

6

100

pA

IIB

Input bias current

VIC = 0,

VO = 0,

See Figure 4

20

175

pA

15

15

VICR

Common-mode input voltage range

RS = 50 

15

to

15

to

V

ICR

g

g

S

– 11

11.9

IO = – 200 

µ

A

13.8

14.1

VOM +

Maximum positive peak output voltage swing

IO = – 2 mA

13.5

13.9

V

IO = – 20 mA

11.5

12.3

IO = 200 

µ

A

– 13.8

– 14.2

VOM –

Maximum negative peak output voltage swing

IO = 2 mA

– 13.5

– 14

V

IO = 20 mA

– 11.5

– 12.4

RL = 600 

80

96

AVD

Large-signal differential voltage amplification

VO = 

±

 10 V

RL = 2 k

90

109

dB

RL = 10 k

95

118

ri

Input resistance

VIC = 0

1012

ci

Input capacitance

VO = 0,

Common mode

7.5

pF

ci

Input capacitance

O

,

See Figure 5

Differential

2.5

pF

zo

Open-loop output impedance

f = 1 MHz

80

CMRR

Common-mode rejection ratio

VIC = VICRmin,

VO = 0,

RS = 50 

80

98

dB

kSVR

Supply-voltage rejection ratio (

VCC

±

/

VIO)

VCC

±

±

5 V to 

±

15 V,

VO = 0,

RS = 50 

82

99

dB

ICC

Supply current

VO = 0,

No load

1.35

1.7

2.2

mA

IOS

Short circuit output current

VO = 0

VID = 1 V

– 30

– 45

mA

IOS

Short-circuit output current

VO = 0

VID = – 1 V

30

48

mA

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

23

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2072C electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

T †

TLE2072C

TLE2072AC

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

VIO

Input offset voltage

25

°

C

0.9

6

0.65

3.5

mV

VIO

Input offset voltage

VIC = 0,

VO = 0,

Full range

7.8

5.3

mV

α

VIO

Temperature coefficient

of input offset voltage

RS = 50 

Full range

2.3

25

2.3

25

µ

V/

°

C

IIO

Input offset current

25

°

C

5

100

5

100

pA

IIO

Input offset current

VIC = 0,

VO = 0,

Full range

1.4

1.4

nA

IIB

Input bias current

IC

,

O

,

See Figure 4

25

°

C

15

175

15

175

pA

IIB

Input bias current

Full range

5

5

nA

5

5

5

5

25

°

C

5

to

5

to

5

to

5

to

VICR

Common-mode input

RS = 50

– 1

– 1.9

– 1

– 1.9

V

VICR

voltage range

RS = 50 

5

5

V

Full range

5

to

5

to

g

– 0.9

– 0.9

IO = 200

µ

A

25

°

C

3.8

4.1

3.8

4.1

IO = – 200 

µ

A

Full range

3.7

3.7

VOM

Maximum positive peak

IO = 2 mA

25

°

C

3.5

3.9

3.5

3.9

V

VOM +

output voltage swing

IO = – 2 mA

Full range

3.4

3.4

V

IO = 20 mA

25

°

C

1.5

2.3

1.5

2.3

IO = – 20 mA

Full range

1.5

1.5

IO = 200

µ

A

25

°

C

– 3.8

– 4.2

– 3.8

– 4.2

IO = 200 

µ

A

Full range

– 3.7

– 3.7

VOM

Maximum negative peak

IO = 2 mA

25

°

C

– 3.5

– 4.1

– 3.5

– 4.1

V

VOM –

g

output voltage swing

IO = 2 mA

Full range

– 3.4

– 3.4

V

IO = 20 mA

25

°

C

– 1.5

– 2.4

– 1.5

– 2.4

IO = 20 mA

Full range

– 1.5

– 1.5

RL = 600

25

°

C

80

91

80

91

RL = 600

Full range

79

79

AVD

Large-signal differential

VO =

±

2 3 V

RL = 2 k

25

°

C

90

100

90

100

dB

AVD

g

g

voltage amplification

VO = 

±

 2.3 V

RL = 2 k

Full range

89

89

dB

RL = 10 k

25

°

C

95

106

95

106

RL = 10 k

Full range

94

94

ri

Input resistance

VIC = 0

25

°

C

1012

1012

ci

Input capacitance

VIC = 0,

See Figure 5

Common

mode

25

°

C

11

11

pF

i

See Figure 5

Differential

25

°

C

2.5

2.5

zo

Open-loop output 

impedance

f = 1 MHz

25

°

C

80

80

CMRR

Common-mode

VIC = VICRmin,

25

°

C

70

89

70

89

dB

CMRR

rejection ratio

IC

ICR

,

VO = 0,

RS = 50 

Full range

68

68

dB

kSVR

Supply-voltage rejection

VCC

±

 = 

±

5 V to

±

15 V,

25

°

C

82

99

82

99

dB

kSVR

y

g

j

ratio(

VCC

±

/

VIO)

CC

±

,

VO = 0,

RS = 50 

Full range

80

80

dB

† Full range is 0

°

C to 70

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

24

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2072C electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V (unless

otherwise noted)

(continued)

PARAMETER

TEST CONDITIONS

T

TLE2072C

TLE2072AC

UNIT

PARAMETER

TEST CONDITIONS

TA

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

ICC

Supply current

VO = 0

No load

25

°

C

2.7

2.9

3.9

2.7

2.9

3.9

mA

ICC

y

(both channels)

VO = 0,

No load

Full range

3.9

3.9

mA

ax

Crosstalk attenuation

VIC = 0,

RL = 2 k

25

°

C

120

120

dB

IOS

Short-circuit output 

VO = 0

VID = 1 V

25

°

C

– 35

– 35

mA

IOS

current

VO = 0

VID = – 1 V

25

°

C

45

45

mA

TLE2072C operating characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V

PARAMETER

TEST CONDITIONS

T †

TLE2072C

TLE2072AC

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

25

°

C

35

35

SR +

Positive slew rate

VO(PP) = 

±

2.3 V,

AVD

1

RL 2 k

Full

range

22

22

V/

µ

s

AVD =  – 1,

RL = 2 k

,

CL = 100 pF,

See Figure 1

25

°

C

38

38

SR –

Negative slew rate

CL = 100  F,

See Figure 1

Full

range

22

22

V/

µ

s

t

Settling time

AVD = – 1,

2-V step,

To 10 mV

25

°

C

0.25

0.25

µ

s

ts

Settling time

,

RL = 1 k

,

CL = 100 pF

To 1 mV

25

°

C

0.4

0.4

µ

s

V

Equivalent input noise

f = 10 Hz

25

°

C

28

55

28

55

nV/

Hz

Vn

q

voltage

f = 10 kHz

25

°

C

11.6

17

11.6

17

nV/

Hz

RS = 20 

,

f = 10 Hz to

6

6

VN(PP)

Peak-to-peak equiva-

lent

S

See Figure 3

10 kHz

25

°

C

6

6

µ

V

VN(PP)

lent

input noise voltage

f = 0.1 Hz to

10 Hz

25

°

C

0.6

0.6

µ

V

In

Equivalent input noise

current

VIC = 0,

f = 10 kHz

25

°

C

2.8

2.8

fA /

Hz

THD + N

Total harmonic distor-

tion

VO(PP) = 5 V,

AVD = 10,

f

1 kHz

RL 2 k

25

°

C

0 013%

0 013%

THD + N

tion

plus noise

f = 1 kHz,

RL = 2 k

,

RS = 25 

25

°

C

0.013%

0.013%

B1

Unity gain bandwidth

VI = 10 mV,

RL = 2 k

,

25

°

C

9 4

9 4

MHz

B1

Unity-gain bandwidth

I

,

L

,

CL = 25 pF,

See Figure 2

25

°

C

9.4

9.4

MHz

BOM

Maximum output-swing

VO(PP) = 4 V,

AVD = – 1,

25

°

C

2 8

2 8

MHz

BOM

g

bandwidth

O(PP)

,

VD

,

RL = 2 k

 

,

CL = 25 pF

25

°

C

2.8

2.8

MHz

φ

Phase margin at unity

VI = 10 mV,

RL = 2 k

,

25

°

C

56

°

56

°

φ

m

g

y

gain

I

L

CL = 25 pF,

See Figure 2

25

°

C

56

°

56

°

† Full range is 0

°

C to 70

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

25

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2072C electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

T †

TLE2072C

TLE2072AC

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

VIO

Input offset voltage

25

°

C

1.1

6

0.7

3.5

mV

VIO

Input offset voltage

VIC = 0,

VO = 0,

Full range

7.8

5.3

mV

α

VIO

Temperature coefficient

of input offset voltage

RS = 50 

Full range

2.4

25

2.4

25

µ

V/

°

C

IIO

Input offset current

25

°

C

6

100

6

100

pA

IIO

Input offset current

VIC = 0,

VO = 0,

Full range

1.4

1.4

nA

IIB

Input bias current

IC

,

O

,

See Figure 4

25

°

C

20

175

20

175

pA

IIB

Input bias current

Full range

5

5

nA

15

15

15

15

25

°

C

15

to

15

to

15

to

15

to

VICR

Common-mode input

RS = 50

– 11

– 11.9

– 11

– 11.9

V

VICR

voltage range

RS = 50 

15

15

V

Full range

15

to

15

to

g

– 10.9

– 10.9

IO = 200

µ

A

25

°

C

13.8

14.1

13.8

14.1

IO = – 200 

µ

A

Full range

13.6

13.6

VOM

Maximum positive peak

IO = 2 mA

25

°

C

13.5

13.9

13.5

13.9

V

VOM +

output voltage swing

IO = – 2 mA

Full range

13.4

13.4

V

IO = 20 mA

25

°

C

11.5

12.3

11.5

12.3

IO = – 20 mA

Full range

11.5

11.5

IO = 200

µ

A

25

°

C

– 13.8

– 14.2

– 13.8

– 14.2

IO = 200 

µ

A

Full range

– 13.7

– 13.7

VOM

Maximum negative peak

IO = 2 mA

25

°

C

– 13.5

– 14

–13.5

– 14

V

VOM –

g

output voltage swing

IO = 2 mA

Full range

– 13.4

– 13.4

V

IO = 20 mA

25

°

C

– 11.5

– 12.4

– 11.5

– 12.4

IO = 20 mA

Full range

– 11.5

– 11.5

RL = 600

25

°

C

80

96

80

96

RL = 600

Full range

79

79

AVD

Large-signal differential

VO =

±

10 V

RL = 2 k

25

°

C

90

109

90

109

dB

AVD

g

g

voltage amplification

VO = 

±

 10 V

RL = 2 k

Full range

89

89

dB

RL = 10 k

25

°

C

95

118

95

118

RL = 10 k

Full range

94

94

ri

Input resistance

VIC = 0

25

°

C

1012

1012

ci

Input capacitance

VIC = 0,

See Figure 5

Common

mode

25

°

C

7.5

7.5

pF

i

See Figure 5

Differential

25

°

C

2.5

2.5

zo

Open-loop output

impedance

f = 1 MHz

25

°

C

80

80

CMRR

Common-mode

VIC = VICRmin,

25

°

C

80

98

80

98

dB

CMRR

rejection ratio

IC

ICR

,

VO = 0,

RS = 50 

Full range

79

79

dB

kSVR

Supply-voltage rejection

VCC

±

 = 

±

5 V to

±

15 V,

25

°

C

82

99

82

99

dB

kSVR

y

g

j

ratio (

VCC

±

/

VIO)

CC

±

,

VO = 0,

RS = 50 

Full range

81

81

dB

† Full range is 0

°

C to 70

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

26

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2072C electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V (unless

otherwise noted)

 

(continued)

PARAMETER

TEST CONDITIONS

T

TLE2072C

TLE2072AC

UNIT

PARAMETER

TEST CONDITIONS

TA

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

ICC

Supply current

VO = 0

No load

25

°

C

2.7

3.1

3.9

2.7

3.1

3.9

mA

ICC

y

(both channels)

VO = 0,

No load

Full range

3.9

3.9

mA

ax

Crosstalk attenuation

VIC = 0,

RL = 2 k

25

°

C

120

120

dB

IOS

Short circuit output current

VO = 0

VID = 1 V

25

°

C

– 30

– 45

– 30

– 45

mA

IOS

Short-circuit output current

VO = 0

VID = – 1 V

25

°

C

30

48

30

48

mA

TLE2072C operating characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V

PARAMETER

TEST CONDITIONS

T †

TLE2072C

TLE2072AC

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

25

°

C

28

40

28

40

SR +

Positive slew rate

VO(PP) = 10 V,

AVD

1

RL 2 k

Full

range

25

25

V/

µ

s

AVD = – 1,

RL = 2 k

,

CL = 100 pF,

See Figure 1

25

°

C

30

45

30

45

SR –

Negative slew rate

CL = 100  F,

See Figure 1

Full

range

25

25

V/

µ

s

t

Settling time

AVD = – 1,

10-V step, 

To 10 mV

25

°

C

0.4

0.4

µ

s

ts

Settling time

,

RL = 1 k

,

CL = 100 pF

To 1 mV

25

°

C

1.5

1.5

µ

s

V

Equivalent input noise

f = 10 Hz

25

°

C

28

55

28

55

nV/

Hz

Vn

q

voltage

f = 10 kHz

25

°

C

11.6

17

11.6

17

nV/

Hz

RS = 20 

,

f  = 10 Hz to

6

6

VN(PP)

Peak-to-peak

equivalent input noise

S

See Figure 3

10 kHz

25

°

C

6

6

µ

V

VN(PP)

equivalent input noise

voltage

f = 0.1 Hz to

10 Hz

25

°

C

0.6

0.6

µ

V

In

Equivalent input noise

current

VIC = 0,

f = 10 kHz

25

°

C

2.8

2.8

fA /

Hz

THD + N

Total harmonic

VO(PP) = 20 V, AVD = 10,

f

1 kHz

RL 2 k

25

°

C

0 008%

0 008%

THD + N

distortion plus noise

f = 1 kHz,

RL = 2 k

RS = 25 

25

°

C

0.008%

0.008%

B1

Unity gain bandwidth

VI = 10 mV,

RL = 2 k

,

25

°

C

8

10

8

10

MHz

B1

Unity-gain bandwidth

I

,

L

,

CL = 25 pF,

See Figure 2

25

°

C

8

10

8

10

MHz

BOM

Maximum output-swing

VO(PP) = 20 V, AVD = – 1,

25

°

C

478

637

478

637

kHz

BOM

g

bandwidth

O(PP)

,

VD

,

RL = 2 k

,

CL = 25 pF

25

°

C

478

637

478

637

kHz

φ

Phase margin at unity

VI = 10 mV,

RL = 2 k

,

25

°

C

57

°

57

°

φ

m

g

y

gain

I

L

CL = 25 pF,

See Figure 2

25

°

C

57

°

57

°

† Full range is 0

°

C to 70

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

27

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2072I electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V (unless otherwise

noted)

PARAMETER

TEST CONDITIONS

T †

TLE2072I

TLE2072AI

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

VIO

Input offset voltage

25

°

C

0.9

6

0.65

3.5

mV

VIO

Input offset voltage

VIC = 0,

VO = 0,

Full range

9.1

6.4

mV

α

VIO

Temperature coefficient

of input offset voltage

RS = 50 

Ω,

Full range

2.4

25

2.4

25

µ

V/

°

C

IIO

Input offset current

25

°

C

5

100

5

100

pA

IIO

Input offset current

VIC = 0,

VO = 0,

Full range

5

5

nA

IIB

Input bias current

IC

,

O

,

See Figure 4

25

°

C

15

175

15

175

pA

IIB

Input bias current

Full range

10

10

nA

5

5

5

5

25

°

C

5

to

5

to

5

to

5

to

VICR

Common-mode input

RS = 50

– 1

– 1.9

– 1

– 1.9

V

VICR

voltage range

RS = 50 

5

5

V

Full range

5

to

5

to

g

– 0.8

– 0.8

IO = 200

µ

A

25

°

C

3.8

4.1

3.8

4.1

IO = – 200 

µ

A

Full range

3.7

3.7

VOM

Maximum positive peak

IO = 2 mA

25

°

C

3.5

3.9

3.5

3.9

V

VOM +

output voltage swing

IO = – 2 mA

Full range

3.4

3.4

V

IO = 20 mA

25

°

C

1.5

2.3

1.5

2.3

IO = – 20 mA

Full range

1.5

1.5

IO = 200

µ

A

25

°

C

– 3.8

– 4.2

– 3.8

– 4.2

IO = 200 

µ

A

Full range

– 3.7

– 3.7

VOM

Maximum negative peak

IO = 2 mA

25

°

C

– 3.5

– 4.1

– 3.5

– 4.1

V

VOM –

g

output voltage swing

IO = 2 mA

Full range

– 3.4

– 3.4

V

IO = 20 mA

25

°

C

– 1.5

– 2.4

– 1.5

– 2.4

IO = 20 mA

Full range

– 1.5

– 1.5

RL = 600

25

°

C

80

91

80

91

RL = 600

Full range

79

79

AVD

Large-signal differential

VO =

±

2 3 V

RL = 2 k

25

°

C

90

100

90

100

dB

AVD

g

g

voltage amplification

VO = 

±

 2.3 V

RL = 2 k

Full range

89

89

dB

RL = 10 k

25

°

C

95

106

95

106

RL = 10 k

Full range

94

94

ri

Input resistance

VIC = 0

25

°

C

1012

1012

ci

Input capacitance

VIC = 0,

See Figure 5

Common

mode

25

°

C

11

11

pF

i

See Figure 5

Differential

25

°

C

2.5

2.5

zo

Open-loop output 

impedance

f = 1 MHz

25

°

C

80

80

CMRR

Common-mode

VIC = VICRmin,

25

°

C

70

89

70

89

dB

CMRR

rejection ratio

IC

ICR

,

VO = 0,

RS = 50 

Full range

68

68

dB

kSVR

Supply-voltage rejection

VCC

±

 = 

±

5 V to

±

15 V,

25

°

C

82

99

82

99

dB

kSVR

y

g

j

ratio (

VCC

±

/

VIO)

CC

±

,

VO = 0,

RS = 50 

Full range

80

80

dB

† Full range is – 40

°

C to 85

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

28

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2072I electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V (unless otherwise

noted)

 

(continued)

PARAMETER

TEST CONDITIONS

T

TLE2072I

TLE2072AI

UNIT

PARAMETER

TEST CONDITIONS

TA

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

ICC

Supply current

VO = 0

No load

25

°

C

2.7

2.9

3.9

2.7

2.9

3.9

mA

ICC

y

(both channels)

VO = 0,

No load

Full range

3.9

3.9

mA

ax

Crosstalk attenuation

VIC = 0,

RL = 2 k

25

°

C

120

120

dB

IOS

Short circuit output current

VO = 0

VID = 1 V

25

°

C

– 35

– 35

mA

IOS

Short-circuit output current

VO = 0

VID = – 1 V

25

°

C

45

45

mA

TLE2072I operating characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V

PARAMETER

TEST CONDITIONS

T †

TLE2072I

TLE2072AI

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

25

°

C

35

35

SR +

Positive slew rate

VO(PP) = 

±

2.3 V,

AVD

1

RL 2 k

Full

range

20

20

V/

µ

s

AVD = – 1,

RL = 2 k

,

CL = 100 pF,

See Figure 1

25

°

C

38

38

SR –

Negative slew rate

CL = 100  F,

See Figure 1

Full

range

20

20

V/

µ

s

t

Settling time

AVD = – 1,

2-V step,

To 10 mV

25

°

C

0.25

0.25

µ

s

ts

Settling time

,

RL = 1 k

,

CL = 100 pF

To 1 mV

25

°

C

0.4

0.4

µ

s

V

Equivalent input noise

f = 10 Hz

25

°

C

28

55

28

55

nV/

Hz

Vn

q

voltage

f = 10 kHz

25

°

C

11.6

17

11.6

17

nV/

Hz

RS = 20 

,

f = 10 Hz to

6

6

VN(PP)

Peak-to-peak 

equivalent input

S

See Figure 3

10 kHz

25

°

C

6

6

µ

V

VN(PP)

equivalent input

noise voltage

f = 0.1 Hz  to

25

°

C

0 6

0 6

µ

V

noise voltage

10 Hz

0.6

0.6

In

Equivalent input noise

current

VIC = 0,

f = 10 kHz

25

°

C

2.8

2.8

fA /

Hz

THD + N

Total harmonic 

VO(PP) = 5 V,

AVD = 10,

f

1 kHz

RL 2 k

25

°

C

0 013%

0 013%

THD + N

distortion plus noise

f = 1 kHz,

RL = 2 k

,

RS = 25 

25

°

C

0.013%

0.013%

B1

Unity gain bandwidth

VI = 10 mV,

RL = 2 k

,

25

°

C

9 4

9 4

MHz

B1

Unity-gain bandwidth

I

,

L

,

CL = 25 pF,

See Figure 2

25

°

C

9.4

9.4

MHz

BOM

Maximum output-

VO(PP) = 4 V,

AVD = – 1,

25

°

C

2 8

2 8

MHz

BOM

swing bandwidth

O(PP)

,

VD

,

RL = 2 k

 

,

CL = 25 pF

25

°

C

2.8

2.8

MHz

φ

Phase margin at unity

VI = 10 mV,

RL = 2 k

,

25

°

C

56

°

56

°

φ

m

g

y

gain

I

L

CL = 25 pF,

See Figure 2

25

°

C

56

°

56

°

† Full range is 40

°

C to 85

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

29

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2072I electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

T †

TLE2072I

TLE2072AI

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

VIO

Input offset voltage

25

°

C

1.1

6

0.7

3.5

mV

VIO

Input offset voltage

VIC = 0,

VO = 0,

Full range

9.1

6.4

mV

α

VIO

Temperature coefficient

of input offset voltage

RS = 50 

Ω,

Full range

2.4

25

2.4

25

µ

V/

°

C

IIO

Input offset current

25

°

C

6

100

6

100

pA

IIO

Input offset current

VIC = 0,

VO = 0,

Full range

5

5

nA

IIB

Input bias current

IC

,

O

,

See Figure 4

25

°

C

20

175

20

175

pA

IIB

Input bias current

Full range

10

10

nA

15

15

15

15

25

°

C

15

to

15

to

15

to

15

to

VICR

Common-mode input

RS = 50

– 11

– 11.9

– 11

– 11.9

V

VICR

voltage range

RS = 50 

15

15

V

Full range

15

to

15

to

g

– 10.8

– 10.8

IO = 200

µ

A

25

°

C

13.8

14.1

13.8

14.1

IO = – 200 

µ

A

Full range

13.7

13.7

VOM

Maximum positive peak

IO = 2 mA

25

°

C

13.5

13.9

13.5

13.9

V

VOM +

output voltage swing

IO = – 2 mA

Full range

13.4

13.4

V

IO = 20 mA

25

°

C

11.5

12.3

11.5

12.3

IO = – 20 mA

Full range

11.5

11.5

IO = 200

µ

A

25

°

C

– 13.8

– 14.2

– 13.8

– 14.2

IO = 200 

µ

A

Full range

– 13.7

– 13.7

VOM

Maximum negative peak

IO = 2 mA

25

°

C

– 13.5

– 14

–13.5

– 14

V

VOM –

g

output voltage swing

IO = 2 mA

Full range

– 13.4

– 13.4

V

IO = 20 mA

25

°

C

– 11.5

– 12.4

– 11.5

– 12.4

IO = 20 mA

Full range

– 11.5

– 11.5

RL = 600

25

°

C

80

96

80

96

RL = 600

Full range

79

79

AVD

Large-signal differential

VO =

±

10 V

RL = 2 k

25

°

C

90

109

90

109

dB

AVD

g

g

voltage amplification

VO = 

±

 10 V

RL = 2 k

Full range

89

89

dB

RL = 10 k

25

°

C

95

118

95

118

RL = 10 k

Full range

94

94

ri

Input resistance

VIC = 0

25

°

C

1012

1012

ci

Input capacitance

VIC = 0,

See Figure 5

Common

mode

25

°

C

7.5

7.5

pF

i

See Figure 5

Differential

25

°

C

2.5

2.5

zo

Open-loop output 

impedance

f = 1 MHz

25

°

C

80

80

CMRR

Common-mode

VIC = VICRmin,

25

°

C

80

98

80

98

dB

CMRR

rejection ratio

IC

ICR

,

VO = 0,

RS = 50 

Full range

79

79

dB

kSVR

Supply-voltage rejection

VCC

±

 = 

±

5 V to

±

15 V,

25

°

C

82

99

82

99

dB

kSVR

y

g

j

ratio (

VCC

±

/

VIO)

CC

±

,

VO = 0,

RS = 50 

Full range

80

80

dB

† Full range is – 40

°

C to 85

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

30

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2072I electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V (unless

otherwise noted)

(continued)

PARAMETER

TEST CONDITIONS

T

TLE2072I

TLE2072AI

UNIT

PARAMETER

TEST CONDITIONS

TA

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

ICC

Supply current

VO = 0

No load

25

°

C

2.7

3.1

3.9

2.7

3.1

3.9

mA

ICC

y

(both channels)

VO = 0,

No load

Full range

3.9

3.9

mA

ax

Crosstalk attenuation

VIC = 0,

RL = 2 k

25

°

C

120

120

dB

IOS

Short circuit output current

VO = 0

VID = 1 V

25

°

C

– 30

– 45

– 30

– 45

mA

IOS

Short-circuit output current

VO = 0

VID = – 1 V

25

°

C

30

48

30

48

mA

TLE2072I operating characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V

PARAMETER

TEST CONDITIONS

T †

TLE2072I

TLE2072AI

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

25

°

C

28

40

28

40

SR +

Positive slew rate

VO(PP) = 

±

10 V,

AVD

1

RL 2 k

Full

range

22

22

V/

µ

s

AVD = – 1,

RL = 2 k

,

CL = 100 pF,

See Figure 1

25

°

C

30

45

30

45

SR –

Negative slew rate

CL = 100  F,

See Figure 1

Full

range

22

22

V/

µ

s

t

Settling time

AVD = – 1,

10-V step,

To 10 mV

25

°

C

0.4

0.4

µ

s

ts

Settling time

,

RL = 1 k

,

CL = 100 pF

To 1 mV

25

°

C

1.5

1.5

µ

s

V

Equivalent input

f = 10 Hz

25

°

C

28

55

28

55

nV/

Hz

Vn

q

noise voltage

f = 10 kHz

25

°

C

11.6

17

11.6

17

nV/

Hz

RS = 20 

,

f = 0 Hz  to

6

6

VN(PP)

Peak-to-peak 

equivalent input

S

See Figure 3

10 kHz

25

°

C

6

6

µ

V

VN(PP)

equivalent input

noise voltage

f = 0.1 Hz to

10 Hz

25

°

C

0.6

0.6

µ

V

In

Equivalent input

noise current

VIC = 0,

f = 10 kHz

25

°

C

2.8

2.8

fA /

Hz

THD + N

Total harmonic

VO(PP) = 20 V, AVD = 10,

f

1 kHz

RL 2 k

25

°

C

0 008%

0 008%

THD + N

distortion plus noise

f = 1 kHz,

RL = 2 k

RS = 25 

25

°

C

0.008%

0.008%

B1

Unity gain bandwidth

VI = 10 mV,

RL = 2 k

,

25

°

C

8

10

8

10

MHz

B1

Unity-gain bandwidth

I

,

L

,

CL = 25 pF,

See Figure 2

25

°

C

8

10

8

10

MHz

BOM

Maximum output-

VO(PP) = 20 V, AVD = – 1,

25

°

C

478

637

478

637

kHz

BOM

swing bandwidth

O(PP)

,

VD

,

RL = 2 k

,

CL = 25 pF

25

°

C

478

637

478

637

kHz

φ

Phase margin at

VI = 10 mV,

RL = 2 k

,

25

°

C

57

°

57

°

φ

m

g

unity gain

I

L

CL = 25 pF,

See Figure 2

25

°

C

57

°

57

°

† Full range is – 40

°

C to 85

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

31

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2072M electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

T †

TLE2072M

TLE2072AM

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

VIO

Input offset voltage

25

°

C

0.9

6

0.65

3.5

mV

VIO

Input offset voltage

VIC = 0,

VO = 0,

Full range

10.5

8

mV

α

VIO

Temperature coefficient

of input offset voltage

RS = 50 

Ω,

Full range

2.3

25

2.3

25

µ

V/

°

C

IIO

Input offset current

25

°

C

5

100

5

100

pA

IIO

Input offset current

VIC = 0,

VO = 0,

Full range

20

20

nA

IIB

Input bias current

IC

,

O

,

See Figure 4

25

°

C

15

175

15

175

pA

IIB

Input bias current

Full range

60

60

nA

5

5

5

5

25

°

C

5

to

5

to

5

to

5

to

VICR

Common-mode input

RS = 50

– 1

– 1.9

– 1

– 1.9

V

VICR

voltage range

RS = 50 

5

5

V

Full range

5

to

5

to

g

– 0.8

– 0.8

IO = 200

µ

A

25

°

C

3.8

4.1

3.8

4.1

IO = – 200 

µ

A

Full range

3.6

3.6

VOM

Maximum positive peak

IO = 2 mA

25

°

C

3.5

3.9

3.5

3.9

V

VOM +

output voltage swing

IO = – 2 mA

Full range

3.3

3.3

V

IO = 20 mA

25

°

C

1.5

2.3

1.5

2.3

IO = – 20 mA

Full range

1.4

1.4

IO = 200

µ

A

25

°

C

– 3.8

– 4.2

– 3.8

– 4.2

IO = 200 

µ

A

Full range

– 3.6

– 3.6

VOM

Maximum negative peak

IO = 2 mA

25

°

C

– 3.5

– 4.1

– 3.5

– 4.1

V

VOM –

g

output voltage swing

IO = 2 mA

Full range

– 3.3

– 3.3

V

IO = 20 mA

25

°

C

– 1.5

– 2.4

– 1.5

– 2.4

IO = 20 mA

Full range

– 1.4

– 1.4

RL = 600

25

°

C

80

91

80

91

RL = 600

Full range

78

78

AVD

Large-signal differential

VO =

±

2 3 V

RL = 2 k

25

°

C

90

100

90

100

dB

AVD

g

g

voltage amplification

VO = 

±

 2.3 V

RL = 2 k

Full range

88

88

dB

RL = 10 k

25

°

C

95

106

95

106

RL = 10 k

Full range

93

93

ri

Input resistance

VIC = 0

25

°

C

1012

1012

ci

Input capacitance

VIC = 0,

See Figure 5

Common

mode

25

°

C

11

11

pF

i

See Figure 5

Differential

25

°

C

2.5

2.5

zo

Open-loop output 

impedance

f = 1 MHz

25

°

C

80

80

CMRR

Common-mode

VIC = VICRmin,

25

°

C

70

89

70

89

dB

CMRR

rejection ratio

IC

ICR

,

VO = 0,

RS = 50 

Full range

68

68

dB

On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.

† Full range is – 55

°

C to 125

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

32

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2072M electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V (unless

otherwise noted)

 

(continued)

PARAMETER

TEST CONDITIONS

T †

TLE2072M

TLE2072AM

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

kSVR

Supply-voltage rejection

ratio (

VCC

±

 /

VIO)

VCC

±

 = 

±

5 V to

±

15 V,

VO = 0,

RS = 50 

Full range

80

80

dB

ICC

Supply current

VO = 0

No load

25

°

C

2.7

2.9

3.6

2.7

2.9

3.6

mA

ICC

y

(both channels)

VO = 0,

No load

Full range

3.6

3.6

mA

ax

Crosstalk attenuation

VIC = 0,

RL = 2 k

25

°

C

120

120

dB

I

Short-circuit output 

V

0

VID = 1 V

25

°

C

– 35

– 35

mA

IOS

current

VO = 0

VID = – 1 V

25

°

C

45

45

mA

† Full range is – 55

°

C to 125

°

C.

TLE2072M operating characteristics at specified free-air temperature, V

CC

±

 = 

±

5 V

PARAMETER

TEST CONDITIONS

T †

TLE2072M

TLE2072AM

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

25

°

C

35

35

SR +

Positive slew rate

VO(PP) = 

±

2.3 V,

AVD

1

RL 2 k

Full

range

18

18

V/

µ

s

AVD = – 1,

RL = 2 k

,

CL = 100 pF,

See Figure 1

25

°

C

38

38

SR –

Negative slew rate

CL = 100  F,

See Figure 1

Full

range

18

18

V/

µ

s

t

Settling time

AVD = – 1,

2-V step,

To 10 mV

25

°

C

0.25

0.25

µ

s

ts

Settling time

,

RL = 1 k

,

CL = 100 pF

To 1 mV

25

°

C

0.4

0.4

µ

s

V

Equivalent input noise

f = 10 Hz

25

°

C

28

55

28

55

nV/

Hz

Vn

q

voltage

f = 10 kHz

25

°

C

11.6

17

11.6

17

nV/

Hz

RS = 20 

,

f = 10 Hz to

6

6

VN(PP)

Peak-to-peak

equivalent input

S

See Figure 3

10 kHz

25

°

C

6

6

µ

V

VN(PP)

equivalent input

noise voltage

f = 0.1 Hz to

25

°

C

0 6

0 6

µ

V

noise voltage

10 Hz

0.6

0.6

In

Equivalent input noise

current

VIC = 0,

f = 10 kHz

25

°

C

2.8

2.8

fA /

Hz

THD + N

Total harmonic

VO(PP) = 5 V,

AVD = 10,

f

1 kHz

RL 2 k

25

°

C

0 013%

0 013%

THD + N

distortion plus noise

f = 1 kHz,

RL = 2 k

RS = 25 

25

°

C

0.013%

0.013%

B1

Unity gain bandwidth

VI = 10 mV,

RL = 2 k

,

25

°

C

9 4

9 4

MHz

B1

Unity-gain bandwidth

I

,

L

,

CL = 25 pF,

See Figure 2

25

°

C

9.4

9.4

MHz

BOM

Maximum output-swing

VO(PP) = 4 V,

AVD = – 1,

25

°

C

2 8

2 8

MHz

BOM

g

bandwidth

O(PP)

,

VD

,

RL = 2 k

 

,

CL = 25 pF

25

°

C

2.8

2.8

MHz

φ

Phase margin at unity

VI = 10 mV,

RL = 2 k

,

25

°

C

56

°

56

°

φ

m

g

y

gain

I

,

L

,

CL = 25 pF,

See Figure 2

25

°

C

56

°

56

°

On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.

† Full range is – 55

°

C to 125

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

33

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2072M electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

T †

TLE2072M

TLE2072AM

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

VIO

Input offset voltage

25

°

C

1.1

6

0.7

3.5

mV

VIO

Input offset voltage

VIC = 0,

VO = 0,

Full range

10.5

8

mV

α

VIO

Temperature coefficient

of input offset voltage

RS = 50 

Full range

2.4

25

2.4

25

µ

V/

°

C

IIO

Input offset current

25

°

C

6

100

6

100

pA

IIO

Input offset current

VIC = 0,

VO = 0,

Full range

20

20

nA

IIB

Input bias current

IC

,

O

,

See Figure 4

25

°

C

20

175

20

175

pA

IIB

Input bias current

Full range

60

60

nA

15

15

15

15

25

°

C

15

to

15

to

15

to

15

to

VICR

Common-mode input

RS = 50

– 11

– 11.9

– 11

– 11.9

V

VICR

voltage range

RS = 50 

15

15

V

Full range

15

to

15

to

g

– 10.8

– 10.8

IO = 200

µ

A

25

°

C

13.8

14.1

13.8

14.1

IO = – 200 

µ

A

Full range

13.6

13.6

VOM

Maximum positive peak

IO = 2 mA

25

°

C

13.5

13.9

13.5

13.9

V

VOM +

output voltage swing

IO = – 2 mA

Full range

13.3

13.3

V

IO = 20 mA

25

°

C

11.5

12.3

11.5

12.3

IO = – 20 mA

Full range

11.4

11.4

IO = 200

µ

A

25

°

C

– 13.8

– 14.2

– 13.8

– 14.2

IO = 200 

µ

A

Full range

– 13.6

– 13.6

VOM

Maximum negative peak

IO = 2 mA

25

°

C

– 13.5

– 14

–13.5

– 14

V

VOM –

g

output voltage swing

IO = 2 mA

Full range

– 13.3

– 13.3

V

IO = 20 mA

25

°

C

– 11.5

– 12.4

– 11.5

– 12.4

IO = 20 mA

Full range

– 11.4

– 11.4

RL = 600

25

°

C

80

96

80

96

RL = 600

Full range

78

78

AVD

Large-signal differential

VO =

±

10 V

RL = 2 k

25

°

C

90

109

90

109

dB

AVD

g

g

voltage amplification

VO = 

±

 10 V

RL = 2 k

Full range

89

89

dB

RL = 10 k

25

°

C

95

118

95

118

RL = 10 k

Full range

93

93

ri

Input resistance

VIC = 0

25

°

C

1012

1012

ci

Input capacitance

VIC = 0,

See Figure 5

Common

mode

25

°

C

7.5

7.5

pF

i

See Figure 5

Differential

25

°

C

2.5

2.5

zo

Open-loop output

impedance

f = 1 MHz

25

°

C

80

80

CMRR

Common-mode

VIC = VICRmin,

25

°

C

80

98

80

98

dB

CMRR

rejection ratio

IC

ICR

,

VO = 0,

RS = 50 

Full range

78

78

dB

kSVR

Supply-voltage rejection

VCC

±

 = 

±

5 V to

±

15 V,

25

°

C

82

99

82

99

dB

kSVR

y

g

j

ratio (

VCC

±

/

VIO)

CC

±

,

VO = 0,

RS = 50 

Full range

80

80

dB

On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.

† Full range is – 55

°

C to 125

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

34

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2072M electrical characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

T †

TLE2072M

TLE2072AM

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

ICC

Supply current

VO = 0

No load

25

°

C

2.7

3.1

3.6

2.7

3.1

3.6

mA

ICC

y

(both channels)

VO = 0,

No load

Full range

3.6

3.6

mA

ax

Crosstalk attenuation

VIC = 0,

RL = 2 k

25

°

C

120

120

dB

IOS

Short-circuit output

VO = 0

VID = 1 V

25

°

C

– 30

– 45

– 30

– 45

mA

IOS

current

VO = 0

VID = – 1 V

25

°

C

30

48

30

48

mA

† Full range is – 55

°

C to 125

°

C.

TLE2072M operating characteristics at specified free-air temperature, V

CC

±

 = 

±

15 V

PARAMETER

TEST CONDITIONS

T †

TLE2072M

TLE2072AM

UNIT

PARAMETER

TEST CONDITIONS

TA†

MIN

TYP

MAX

MIN

TYP

MAX

UNIT

25

°

C

28

40

28

40

SR +

Positive slew rate

VO(PP) = 10 V,  AVD = – 1,

RL 2 k

CL 100 pF

Full

range

20

20

V/

µ

s

RL = 2 k

,

CL = 100 pF,

See Figure 1

25

°

C

30

45

30

45

SR –

Negative slew rate

See Figure 1

Full

range

20

20

V/

µ

s

t

Settling time

AVD = – 1,

10-V step, 

To 10 mV

25

°

C

0.4

0.4

µ

s

ts

Settling time

,

RL = 1 k

,

CL = 100 pF

To 1 mV

25

°

C

1.5

1.5

µ

s

V

Equivalent input noise

f = 10 Hz

25

°

C

28

55

28

55

nV/

Hz

Vn

q

voltage

f = 10 kHz

25

°

C

11.6

17

11.6

17

nV/

Hz

RS = 20 

,

f  = 10 Hz to

6

6

VN(PP)

Peak-to-peak

equivalent input

S

See Figure 3

10 kHz

25

°

C

6

6

µ

V

VN(PP)

equivalent input 

noise voltage

f  = 0.1 Hz to

25

°

C

0 6

0 6

µ

V

noise voltage

10 Hz

0.6

0.6

In

Equivalent input noise

current

VIC = 0,

f = 10 kHz

25

°

C

2.8

2.8

fA /

Hz

THD + N

Total harmonic

VO(PP) = 20 V, AVD = 10,

f

1 kHz

RL 2 k

25

°

C

0 008%

0 008%

THD + N

distortion plus noise

f = 1 kHz,

RL = 2 k

RS = 25 

25

°

C

0.008%

0.008%

B1

Unity gain bandwidth

VI = 10 mV,

RL = 2 k

,

25

°

C

8

10

8

10

MHz

B1

Unity-gain bandwidth

I

,

L

,

CL = 25 pF,

See Figure 2

25

°

C

8

10

8

10

MHz

BOM

Maximum

output swing

VO(PP) = 20 V, AVD = – 1,

25

°

C

478

637

478

637

kHz

BOM

output-swing

bandwidth

O(PP)

,

VD

,

RL = 2 k

,

CL = 25 pF

25

°

C

478

637

478

637

kHz

φ

Phase margin at unity

VI = 10 mV,

RL = 2 k

,

25

°

C

57

°

57

°

φ

m

g

y

gain

I

L

CL = 25 pF,

See Figure 2

25

°

C

57

°

57

°

On products compliant to MIL-PRF-38535, Class B, this parameter is not production tested.

† Full range is – 55

°

C to 125

°

C.

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

35

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2072Y electrical characteristics at V

CC

±

 = 

±

15 V, T

A

 = 25

°

C

PARAMETER

TEST CONDITIONS

TLE2072Y

UNIT

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

VIO

Input offset voltage

VIC = 0,

VO = 0, RS = 50 

1.1

6

mV

IIO

Input offset current

VIC = 0

VO = 0

See Figure 4

6

100

pA

IIB

Input bias current

VIC = 0,

VO = 0, See Figure 4

20

175

pA

15

15

VICR

Common-mode input voltage range

RS = 50 

15

to

15

to

V

ICR

g

g

S

– 11

11.9

IO = – 200 

µ

A

13.8

14.1

VOM +

Maximum positive peak output voltage swing

IO = – 2 mA

13.5

13.9

V

IO = – 20 mA

11.5

12.3

M

i

ti

k

IO = 200 

µ

A

– 13.8

– 14.2

VOM –

Maximum negative peak

output voltage swing

IO = 2 mA

– 13.5

– 14

V

out ut voltage swing

IO = 20 mA

– 11.5

– 12.4

RL = 600 

80

96

AVD

Large-signal differential voltage amplification

VO = 

±

 10 V

RL = 2 k

90

109

dB

RL = 10 k

95

118

ri

Input resistance

VIC = 0

1012

ci

Input capacitance

VIC = 0,

Common mode

7.5

pF

ci

Input capacitance

IC

,

See Figure 5

Differential

2.5

pF

zo

Open-loop output impedance

f = 1 MHz

80

CMRR

Common-mode rejection ratio

VIC = VICRmin,

VO = 0, RS = 50 

80

98

dB

kSVR

Supply-voltage rejection ratio (

VCC

±

/

VIO)

VCC

±

±

5 V to 

±

15 V,

VO = 0,

RS = 50 

82

99

dB

ICC

Supply current (both channels)

VO = 0,

No load

2.7

3.1

3.9

mA

I

Short circuit output current

V

0

VID = 1 V

– 30

– 45

mA

IOS

Short-circuit output current

VO = 0

VID = – 1 V

30

48

mA

background image

TLE207x, TLE207xA, TLE207xY

EXCALIBUR LOW-NOISE HIGH-SPEED

JFET-INPUT OPERATIONAL AMPLIFIERS

SLOS181A – FEBRUARY 1997 – REVISED MARCH 2000

36

POST OFFICE BOX 655303 

 DALLAS, TEXAS 75265

TLE2074C elec